Showing 1–24 of 73 results
-
(SW-420) Vibration Sensor Module
₹99.00₹59.00- Using SW-420 normally closed type vibration sensor
- Comparator output, clean signal, good waveform, strong driving ability >15mA
- Operating Voltage: 3.3V ~ 5V
- Output Format: digital switching output (0 and 1)
- Using a wide voltage LM393 comparator
- With bolt holes for easy installation
-
100A Non-IVCASIVE Split Core Ac Current Sensor SCT013
₹999.00₹618.00- Non-invasive current transformer
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
- Two form of output current, voltage (voltage output built-in the sampling resistor)
- Non-linearity 3%(10%-120% rated input current)
- Output Plug 3.5mm
-
12 LED MULTI COLOUR MIST MAKER 24V DC 1M WIRE MISTM
₹499.00₹399.00- 12 Led Mist Maker Fog Smoke Machine Water Fountain Pond Pot Aquarium.
- Transpose your atmosphere into a beautiful stunning ambience whenever you wish with this colourful smoky magical mist forger machine.
- Easy to operate, the fog is cold and absolutely harmless, no heat or chemicals used. The dry ice effect without the dry ice! New built in Red, Yellow & Blue 12 LED Lights change colour every few seconds.
- Widely used in aquariums, interior decoration, fragrance beauty, rockery and pool indoor and outdoor projects, landscape garden, small nagareizumi, bonsai, medical atomization and many area.
-
12V Battery Energy Storage Spot Welding PCB Circuit Board
₹2,599.00₹2,099.00- Working Current (A):90-150
- Supply Voltage(V):12-15
- Welding Current(A):90-130
- Length (mm):80
- Width (mm):45
- Cable Length(cm):36
- Weight (gm):146
-
12V SPOT WELDING MACHINE DIY PORTABLE BATTERY WELDM
₹999.00₹899.00- Through the MOS tube output, this energy will be concentrated at the end of the welding pen, and it will be heated by short circuit.
- Lightweight and portable, stable and reliable, wear resistant and can provides long service time.
- Suitable for welding 186502665032650 battery.
- Fuse the nickel sheet family with the battery.
- It is precisely controlled by the single-chip microcomputer program without trigger switch.
-
16CH ANALOG/DIG MULTIPLEXER BREAKOUT MODULE CD74HC
₹99.00₹49.00- This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
- This chip is like a rotary switch – it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (Chinx).
- It works with both digital and analogue signals (the voltage can’t be higher than VCC), and the connections function in either direction.
- To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want (see the datasheet for details).
- This allows you to connect up to 16 sensors to your system using only 5 pins! 2.
- Since the mux/demuxer also works with digital signals, you can use it to pipe TTL-level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller.
- You can then select any one of those 16 devices to listen to.
- If you want two-way communications, you can add a second board to route your microcontroller’s TX line to 16 device’s RX lines.
- By using multiple boards, you can create similar arrangements for I2C, SPI, etc. 3.
- The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching.
- The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”).
-
2.4″ TFT Pocket Size Digital Oscilloscope Kit DIY DSO138
₹2,999.00₹1,999.00- This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch colour TFT display screen.
- Adjustable vertical displacement, and with instructions.
- With automatic, regular and one-shot modes, easy to capture the moment waveform.
- Available rising or falling edge trigger.
- Observable previous trigger waveform (negative delay).
- Can freeze at any time waveform display (the HOLD function).
- Maximum Real-time Sampling Rate: 1Msps
- Accuracy: 12Bit
- Sampling Buffer Depth: 1024 bytes
- Analog Bandwidth: 0-200KHz
-
20A Range Current Sensor Module ACS712
₹199.00₹129.00- Low-noise Analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
-
3144 TO-92 Hall Effect Sensor
₹129.00₹75.00- 3.5V to 24V DC operation voltage
- Low current consumption
- Temperature compensation
- Wide operating voltage range
- Open-Collector pre-driver
- 50mA maximum sinking output current
- Reverse polarity protection
-
360 Degree Green Rotary Encoder Module
₹199.00₹99.00- Incremental Encoder
- Supply Voltage: 3-5V
- Left/Right rotary output pulse, each circle with 20 pulse
- Built in 10k resistor
- Cycles per revolution (CPR): 20
-
3D PRINTER PARTS MECHANICAL ENDSTOP RAMES
₹99.00₹49.00- Mechanical Endshop Limit Switch with 70cm 3-Pin Connecting Cable High Quality Switch Element: Made of 22AWG wire, thick copper wire resistant to 2A current 300V voltage, up to 80 degree large temperature range of insulating layer.
- Suitable for RepRap 3D Printer or CNC tool, supporting by RepRap electronics, RMAPS 1.4 and other common used RepRap board. 22AWG connecting line, thick internal copper core, withstanding 2A current, 300V voltage. Max insulation temperature of insulating layer up to 80 degree
- Convenient to Use: Equipped with 3Pin male/female connector head, plug and play, easy to install.
- Red line connect to VCC (ramps +), Black line connect to GND (ramps -), Green line connect to SIGNAL (ramps s)
- Easy to install, hard to snap, convenient to plug or release.
-
4CH RC Remote Control 27mhz Circuit PCB Transmitter & Receiver Board with Antenna Radio System for Toy Car
Electronic Modules, LEARNING & ROBOTICS KIT, NEW ARRIVALS, OTHER SENSOR & MODULES, RF Wireless Modules₹199.00₹125.00- Electronic frequency: 27MHZ
- Dimensions: TX Board 3.9 * 5.7 cm, RX Board 2.7 * 4.2 cm;
- Working voltage: 4.5V for transmitter board, 4.5v-6v for Receiving board
- Output voltage: Output two way voltage about 2v-3.5v, can control 2x motors positive and negative, 1-3V motor can be used.
- Receiver operating voltage: 3.7–6V
- Transmitter operating voltage: 3.7-9V (HW Battery)
- Transmitter Range: 12-15 (approx)
- Color: Brown
- Material: fiberglass
- Electronic frequency: 27MHZ
- Dimensions: pad 3 * 9 cm, receiving plate 3.5 * 2 cm, Antenna, 19 cm
- Item Weight: 16g
-
5-36V Switch Drive High-Power MOSFET Trigger Module
₹99.00₹89.00- Dual MOSFET
- Trigger Source: 3.3V to 20V DC
- Signal Frequency: 0-20KHz Supported
- Output Drive Capacity: 5V to 36V DC
- Continuous Current: 15A at Room Temperature
-
650nm 6mm 5V DC 5mW Mini Laser Dot Diode Module (Pack of 2)
₹89.00₹59.00- Output Power: 5mW
- Working Voltage: 5V DC
- Working temperature: -10 ℃~+40 ℃
- Housing material: Copper
- Working life: more than 2000 hours
- Spot mode: Dot Facula (continuous output)
- Laser wavelength: 650nm red-colored.
- Operating current: <40mA
- Power lead length: 120mm.
-
6MM SIZE 650NM 5MW LASER DIODE LASERD
₹99.00₹49.00- Outer diameter: 6MM.
- Cable length: Approx. 2.4cm.
- Diode diameter: Approx.0.6cm.
- Working voltage: 5v DC
-
A3144 Hall Effect Sensor Module
₹99.00₹49.00- Digital Output Hall-effect sensor.
- Operating voltage: typically 5V.
- Output Current: 25mA.
- It can be used to detect both the poles of a magnet.
-
AC Voltage Sensor Module ZMPT101B (Single Phase)
₹199.00₹129.00- Voltage – 250V
- Easy PCB mounting
- Good consistency
- Widely acclaimed
-
ACS712 – 30A Range Current Sensor Module
₹199.00₹129.00- Supply Voltage: 4.5V ~ 5.5V DC
- Measure Current Range: -30A ~ 30A
- Sensitivity: 100mV/A
-
ACS712 5A range Current Sensor Module
₹199.00₹129.00- Low-noise analog signal path.
- Device bandwidth is set via the new FILTER pin.
- 5 µs output rise time in response to step input current.
- Small footprint, low-profile SOIC8 package.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
-
ADS1115 16-Bit I2C ADC 4-Channel Programmable Gain Amplifier Module
₹449.00₹399.00- WIDE SUPPLY RANGE: 2.0V to 5.5V
- PROGRAMMABLE DATA RATE: 8SPS to 860SPS
- It has an Internal low-drift voltage reference
- Internal Oscillator.
- Internal PGA.
- I2C INTERFACE : Pin-Selectable Addresses.
- Four single ends Or Two differential inputs.
-
CJMCU-219 I2C Power Supply Monitoring Module INA219
₹499.00₹239.00- 0.1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- 2C- or Sambas-compatible interface. The
- Reports Current, Voltage, and Power.
-
CJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module
₹499.00₹299.00- 0.1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- 2C- or SMBus-compatible interface. The
- Reports Current, Voltage, and Power.
-
CNC 3D Printer Mechanical EndStop Switch
₹99.00₹79.00- Wire type: 22AWG
- Working voltage: 300V
- Working Current: 2A
- Temperature resistance: 80° C
- Cable length: 70cm
-
Colour Recog. Sensor Module TCS3200 /TCS230
₹899.00₹599.00- imported chips TCS3200 PCB board with gold plating
- TCS3200 is the TCS230 upgrade version, the better
- Power supply 3-5v
- anti-light interference
- white LED can control the on and off.
- can detect non-luminous object colour
- High-resolution conversion of light intensity to frequency.
- Chip pins all have drawn for standard 100.
- Put the needle (2.54 mm).
- Mil-convenient for bitmap board.
- Programmable colour and full-scale output frequency.
- Communicate directly with a microcontroller.
- Low-profile surface-mount package.