Showing 1–25 of 67 results
-
0.5V TO 4.20 MA VOLTAGE-TO-CURRENT MODULE VC05M
₹699.00₹350.00Add to cart- power supply: DC 7-30 V
- Input Voltage: 0-10V
- Output current: 4-20mA
- drifting temperature: +/- 100ppm /
- Ambient temperature: -10 ~ 60
- Storage temperature: -20 ~ 85
- Relative Humidity: 10-90% RH
- air pressure: 86-106Kpa
-
100A Non-IVCASIVE Split Core Ac Current Sensor SCT013
₹999.00₹618.00Add to cart- Non-invasive current transformer
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
- Two form of output current, voltage (voltage output built-in the sampling resistor)
- Non-linearity 3%(10%-120% rated input current)
- Output Plug 3.5mm
-
12V SPOT WELDING MACHINE DIY PORTABLE BATTERY WELDM
₹3,999.00₹1,299.00Add to cart- Portable & Compact – Lightweight design, easy to carry for on-the-go battery repairs
- 12V DC Powered – Runs on a 12V battery or DC power supply for flexible use
- DIY-Friendly – Simple to assemble and operate, no professional skills required
- High Welding Current – Delivers strong spot welds (up to 650A depending on power source)
- Wide Compatibility – Works with 18650, 26650, and various cylindrical lithium batteries
- Nickel Strip Support – Ideal for welding nickel strips 0.1mm to 0.2mm thick
-
16CH ANALOG/DIG MULTIPLEXER BREAKOUT MODULE CD74HC
₹99.00₹59.00Add to cart- This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
- This chip is like a rotary switch – it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (Chinx).
- It works with both digital and analogue signals (the voltage can’t be higher than VCC), and the connections function in either direction.
- To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want (see the datasheet for details).
- This allows you to connect up to 16 sensors to your system using only 5 pins! 2.
- Since the mux/demuxer also works with digital signals, you can use it to pipe TTL-level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller.
- You can then select any one of those 16 devices to listen to.
- If you want two-way communications, you can add a second board to route your microcontroller’s TX line to 16 device’s RX lines.
- By using multiple boards, you can create similar arrangements for I2C, SPI, etc. 3.
- The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching.
- The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”).
-
2.4 inch TFT Handheld Pocket-size Digital Oscilloscope Kit DIY Parts Electronic Learning Set Soldered DSO138
₹4,999.00₹1,780.00Add to cart- his kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen.
- Accuracy: 12Bit
- Adjustable vertical displacement, and with instructions.
- Available rising or falling edge trigger.
- Analog Bandwidth: 0-200KHz
-
20A Range Current Sensor Module ACS712
₹199.00₹129.00Add to cart- Low-noise Analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
-
3144 TO-92 Hall Effect Sensor
₹129.00₹75.00Add to cart- 3.5V to 24V DC operation voltage
- Low current consumption
- Temperature compensation
- Wide operating voltage range
- Open-Collector pre-driver
- 50mA maximum sinking output current
- Reverse polarity protection
-
360 GREEN ROTARY ENCODER MODULE FOR AUDUINO AB156
₹199.00₹79.00Add to cart- Widely used for various electrical projects.
- Light weight, small size, easy to carry.
- Esay install & no driver needed.
- Imported from hongkong
-
3D PRINTER PARTS MECHANICAL ENDSTOP RAMES
₹159.00₹89.00Add to cart- Mechanical Endshop Limit Switch with 70cm 3-Pin Connecting Cable High Quality Switch Element: Made of 22AWG wire, thick copper wire resistant to 2A current 300V voltage, up to 80 degree large temperature range of insulating layer.
- Suitable for RepRap 3D Printer or CNC tool, supporting by RepRap electronics, RMAPS 1.4 and other common used RepRap board. 22AWG connecting line, thick internal copper core, withstanding 2A current, 300V voltage. Max insulation temperature of insulating layer up to 80 degree
- Convenient to Use: Equipped with 3Pin male/female connector head, plug and play, easy to install.
- Red line connect to VCC (ramps +), Black line connect to GND (ramps -), Green line connect to SIGNAL (ramps s)
- Easy to install, hard to snap, convenient to plug or release.
-
5-36V SWITCH DRIVE MOSFET TRIGGER MODULE AA517
₹99.00₹89.00Add to cart- Dual MOSFET
- Trigger Source: 3.3V to 20V DC
- Signal Frequency: 0-20KHz Supported
- Output Drive Capacity: 5V to 36V DC
- Continuous Current: 15A at Room Temperature
-
650nm 6mm 5V DC 5mW Mini Laser Dot Diode Module (Pack of 2)
₹89.00₹59.00Add to cart- Output Power: 5mW
- Working Voltage: 5V DC
- Working temperature: -10 ℃~＋40 ℃
- Housing material: Copper
- Working life: more than 2000 hours
- Spot mode: Dot Facula (continuous output)
- Laser wavelength: 650nm red-colored.
- Operating current: <40mA
- Power lead length: 120mm.
-
6MM SIZE 650NM 5MW LASER DIODE LASERD
₹199.00₹79.00Add to cart- 5V 650nm 5mW Red Dot Diode Laser Head Red Laser Diode 6mm Red Laser Diode Laser Head
- Wave length: 650nm
- Wide range of wroking temperature: -10°C to +40°C
- Application: Level instrument, Ground instrument, Long distance laser listener remote light control, Long distance laser wireless communication
-
A3144 Hall Effect Sensor Module
₹99.00₹49.00Add to cart- Digital Output Hall-effect sensor.
- Operating voltage: typically 5V.
- Output Current: 25mA.
- It can be used to detect both the poles of a magnet.
-
AC VOLTAGE SENSOR MODULE ZMPT101B SINGLE PHASE Z101B
₹199.00₹129.00Add to cart- Voltage – 250V
- Easy PCB mounting
- Good consistency
- Widely acclaimed
-
ACS712 – 30A Range Current Sensor Module
₹199.00₹129.00Add to cart- Supply Voltage: 4.5V ~ 5.5V DC
- Measure Current Range: -30A ~ 30A
- Sensitivity: 100mV/A
-
ACS712 5A range Current Sensor Module
₹199.00₹129.00Add to cart- Low-noise analog signal path.
- Device bandwidth is set via the new FILTER pin.
- 5 µs output rise time in response to step input current.
- Small footprint, low-profile SOIC8 package.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
-
ADS1115 16-Bit I2C ADC 4-Channel Programmable Gain Amplifier Module AD1115
₹599.00₹199.00Add to cart- WIDE SUPPLY RANGE: 2.0V to 5.5V
- PROGRAMMABLE DATA RATE: 8SPS to 860SPS
- It has an Internal low-drift voltage reference
- Internal Oscillator.
- Internal PGA.
- I2C INTERFACE : Pin-Selectable Addresses.
- Four single ends Or Two differential inputs.
-
CJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module INA219
₹499.00₹299.00Add to cart- 0.1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- 2C- or SMBus-compatible interface. The
- Reports Current, Voltage, and Power.
-
CNC 3D Printer Mechanical EndStop Switch
₹99.00₹79.00Add to cart- Wire type: 22AWG
- Working voltage: 300V
- Working Current: 2A
- Temperature resistance: 80° C
- Cable length: 70cm
-
DC-DC ADJUSTABLE STEP DOWN MODULE 4~38V 5A XL4015
₹259.00₹159.00Add to cart- Input voltage range:4~38VDC(Note:input voltage not exceeding 38V)
- Output voltage range:1.25-36VDC adjustable
- Output current: 0-5A, recommended for use in 4.5A.
- Output power: 75W 5.Working temperature: -40~+85 degrees
- Operating frequency: 180KHz
- Efficiency:96%(max)
- Short circuit protection: yes(limit current 8A).
- Over temperature protection
- Input reverse polarity protection: None (if required, high current diode in series with the input).
- L x W x H = 54 * 23 * 18mm
-
DC5V HUMIDIFIER USB SPRAY MODULE 108KHZ HUM108
₹149.00₹110.00Add to cart- Product Name: 108KHz 20mm USB Humidifier
- Work Voltage: DC 4.5V~5.0V
- Work Power:2W
- Work Frequency:108KHz(+/-3KHz)
- Power Type: Female USB Socket
- Diameter without rubber ring:16mm
- Diameter with rubber ring:20mm
- Spray Diameter:5um
- Spray Hole:740 holes
- Spray speed:50ml/h
- Work Temperature:0℃ ~ 85℃
- Work Humidity:10%~90%RH
- Driver Size:35*19*15mm
- Length: 35 mm
- Width: 19 mm
- Height: 15 mm
- Weight: 10 gm
-
Digital LDR Module – 3 Pin
₹49.00₹39.00Add to cart- LM393 based design.
- Can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- LEDs indicating output and power.
- Operating Voltage: 3.3V to 5V DC.
- Operating Current: 15ma.
-
DIP 3 Color LED Module COL3
₹199.00₹49.00Add to cart- The use of plug-in full-colour LED.
- RGB trichromatic limiting resistor to prevent burnout.
- With a variety of single-chip interface.
- Through the PWM adjusting, three primary colors can be mixed to obtain different colors
- The working voltage: 5V
-
DOUBLE SPEED MEASURING SENSOR MODULE HC020
₹249.00₹199.00Read more- Dual-Sensor System – Measures speed by calculating time difference between two sensors for higher accuracy.
- High Precision Speed Detection – Suitable for measuring both linear and rotational speed.
- Digital Output – Easy-to-read pulse signals compatible with most microcontrollers.
- Wide Speed Range – Accurately detects objects moving at variable speeds (up to 5 m/s).
- Real-Time Data – Quick response time (<5 ms) for dynamic applications.
- Microcontroller Friendly – Works seamlessly with Arduino, Raspberry Pi, STM32, and other platforms.
- Compact & Lightweight – Easy to mount and integrate into small enclosures or systems.
- Low Power Consumption – Operates on 3.3V to 5V DC supply.
- Reliable in Various Conditions – Operates effectively in temperatures ranging from -20°C to 70°C.
- Versatile Applications – Ideal for robotics, conveyor belts, motor monitoring, and automation systems.
-
Dry Reed Sensor Module Magnetic Switch REED
₹99.00₹59.00Add to cart- Open reed switch
- Working voltage: 3.3V ~ 5V
- Current: Upto 1.2A
- Comparator output, clean signal, great waveform, and strong driving ability
- Digital switch output (0 and 1)
- Fixed bolt hole for easy installation
