Showing all 24 results
-
37 in 1 Sensor Kit Compatible with Arduino
Arduino Compatible Kits, DEVELOPMENT BOARDS, LEARNING & ROBOTICS KIT, Robotic and DIY Kits, Sensor Kits, Sensors & Modules₹999.00₹899.00- 37 Sensors To DIY Kit
- Can Be Used With Arduino, Raspberry Pi, AVR, PIC, 8051
- Good Quality, Easy To Use And Learn.
- Skill Level: Beginners To Advance Level.
- Can Be Used For Prototype Purpose.
-
ADK USB Host Shield For Arduino AUSBS
₹999.00₹599.00- USB Host Shield support the Google Android ADK and Android Phone: G1, Nexus One, Nexus S, Motorola Droid X. (Note:Mobile phone system needs to upgrade Android 2.3.4, Tablet PC needs to upgrade to Android 3.1).
- Compatible with following hardware: for Arduino Mega 2560 (Recommended); for Arduino Mega 1280; for Arduino Uno 328; for Arduino Diecimila / Duemilanove 328.
- When achieves the USB HOST function, USB Host Shield can communicate with other USB devices, support USB HUB function as well.
- The USB power pin have the 3.3Vin and 5Vin pins, which needs to be soldered for the shield to work.
- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
- Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).
-
Arduino NANO V3.0 Development Board – Clone Compatible Model(Soldered)
₹599.00₹299.00- Microcontroller Atmel ATmega328 SMD Package
- Operating Voltage (logic level) 5 V
- Input Voltage (recommended) 7-12 V
- Input Voltage (limits) 6-20 V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins 8
- DC Current per I/O Pin 40 mA
- Flash Memory 32 KB (of which 2KB used by bootloader)
- SRAM 2 KB
- EEPROM 1 KB
- Clock Speed 16 MHz
- Dimensions 0.70” x 1.70”
-
Arduino NANO V3.0 Development Board Unsoldered
₹899.00₹699.00- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Support USB download and Power
- Support for external 5V ~ 12V DC power supply
- Support power supply by 9V battery
- Support ISP download
- Automatic reset during program download.
- Power OK blue LED on the bottom.
- Green (TX), red (RX) and orange (L) LED.
- +5V to AREF jumper.
- Auto sensing/switching power input.
- Small mini-B USB for programming and serial monitor.
- ICSP header for direct program download.
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
-
Arduino NANO V3.0 Unsoldered ANANO
₹399.00₹249.00- Microcontroller-Atmel ATmega328 SMD Package
- Operating Voltage (logic level)-5 V
- Input Voltage (recommended)-7-12 V
- Input Voltage (limits)-6-20 V
- Digital I/O Pins- 14 (of which 6 provide PWM output)
- Analog Input Pins-8
- DC Current per I/O Pin- 40 mA
- Flash Memory- 32 KB (of which 2KB used by bootloader)
- SRAM-2 KB
- EEPROM-1 KB
- Clock Speed-16 MHz
- Dimensions-0.70” x 1.70”
-
ARDUINO SENSOR SHIELD V-5 ASENS
₹199.00₹99.00- Retain the merits of the V4.0 version
- Laminated design
- PCB immersion gold processing technology
- IIC interface
- Bluetooth module communication interface
- SD card module communication interface
- APC220 wireless rf modules communication interface
- RB URF v1.1 ultrasonic sensors interface
- 12864 LCD string of line and parallel interface
- 32 servo controller interface
-
Arduino UNO NANO V30 Soldered NANOS
₹499.00₹299.00- Arduino Nano V3.0 ATMEGA328
- The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328
- Operating Voltage: 5V Input Voltage: 7V ~ 12V Input Voltage (limits): 6V ~ 20 V
- Flash Memory: 32KB (ATmega328) (of which 2 KB used by bootloader) SRAM: 2KB (ATmega328)
- EEPROM: 1KB (ATmega328) Clock Speed: 16MHz
- Kit Contains: Soldered Nano compatible, Nano Cable Mini USB to USB
-
ARDUINO UNO R3 DIP UNOR3
₹999.00₹549.00- 14 digital input/output pins,
- 6 analogue inputs,
- 16 MHz crystal oscillator,
- USB connection,
- power jack,
- ICSP header
-
Arduino UNO SMD UNOSM
₹699.00₹299.00- ATmega328P SMD Microcontroller: Features the surface-mount version of the popular ATmega328P for a more compact and durable design.
- 14 Digital I/O Pins: Includes 14 digital pins, 6 of which can be used as PWM outputs for controlling motors, LEDs, and more.
- 6 Analog Inputs: Provides 6 analog input pins for reading sensors or other analog devices.
- Built-in USB Connectivity: USB Type-B port for easy connection to computers for programming and serial communication.
- PWM Outputs: 6 digital pins support Pulse Width Modulation (PWM), ideal for controlling devices with variable output like motors and LEDs.
- 5V Operating Voltage: Designed to run at 5V for stable performance in most DIY and embedded projects.
- Power Supply Flexibility: Can be powered via USB or a 9V DC adapter, providing convenience in setup.
- Open-Source Platform: Fully open-source hardware and software, offering flexibility for customization and creative development.
- Compact Size: Measures 68.6mm x 53.4mm, making it ideal for space-constrained projects.
- Easy-to-Use IDE: Compatible with the Arduino IDE for easy coding, compiling, and uploading to the board.
- Wide Community Support: Access to an extensive online community with tutorials, examples, and troubleshooting guides.
-
Blue Nano Io Shield V1.0 Expansion Board NA005E
₹199.00₹107.00- Type: Voltage Regulator
- Supply Voltage: 3 – 5V
- Compatible with Arduino NANO
- All digital and analogue pins breakout
- Compact size
- Leads all pins out, convenient for wiring and doing experiments.
-
CNC SHIELD V3 ENGRAVING MACHINE CNCV3
₹199.00₹139.00- The extension board can be used for Small CNC routers, Carving Machine, 3D Printers, DIY Laser Cutters, and almost any project where you need to control a stepper motors with high precision
- This shield allows you to control upto 4 stepper motors
- Controller each stepper motor requires 2 IO Pins only, which saves a lot of IO Pins for other purposes
- Arduino compatible
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Supports PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- Supports Coolant enable
- Supports removable A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Uses removable A4988 or DRV8825 compatible stepping driver.
-
DTH Power Supply Circuit Board for Free to Air D2H DTH Set Top Box Satellite
₹299.00₹159.00- Input : 220 V AC
- Switch Mode Circuit(SMPS) – No transformer
- Output : DC voltage via 6 pin header(+33V, Gnd, +12V, +24V, Gnd
- This power supply board is compatible with most common brands
-
LilyPad 328 ATmega328P Main Board 16M Compatible with Arduino
₹1,299.00₹499.00- Microcontroller: ATmega328P
- Operating Voltage: 2.7-5.5 V
- Digital I/O Pins: 14
- PWM Channels: 6
- Analog Input Channels: 6
- DC Current per I/O Pin: 40 mA
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
-
Mega 2560 R3 MEGAR3
₹1,999.00₹1,399.00- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 256 KB of which 8 KB used by bootloader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
- USB Host Chip: MAX3421E
- Length:101.98mm/4.01in
- Width:53.63mm/2.11in
- Height:15.29mm/0.60in
-
Motor Driver Shield Expansion Board For Arduino (L293D)
₹449.00₹229.00- This L293D Motor Driver Shield for microcontrollers is versatile and features 2 servo and 4 motor connectors for DC or stepper motors. It is a great shield for any robotic project.
- Up to 4 bi-directional DC motors | Up to 2 stepper motors | Pull down resistors | Reset button | Big terminal block connectors | Screw terminal connectors for easy motor connection | High noise immunity inputs
- Dimensions(LxWxH):70x54x18 mm
- The bipolar pulse width method of L293D motor driver has many advantages, such as the current continuous, or microcurrent vibration when the motor stops. It can eliminate the dead zone of static friction when positive and negative.
- Continuous Output Current:1.2A Logic control voltage:4.5V to 5.5V 4 H-Bridges:L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection and internal kickback protection diodes
-
NANO EXPANSION ADAPTER BREAKOUT BOARD IO SHIELD NA005
₹399.00₹199.00- Compatibility: Designed for Arduino Nano (ATmega328P).
- Expanded I/O Access: Easily connects additional components and sensors.
- Breadboard Friendly: Compact size fits standard breadboards for prototyping.
- Clear Pin Labeling: Pins are clearly marked for straightforward wiring.
- Built-in Voltage Regulator: Provides stable power supply to connected devices.
- Versatile Communication Options: Includes headers for SPI, I2C, and UART.
- Durable Construction: Made from high-quality materials for reliability.
- Lightweight Design: Portable and easy to integrate into projects.
- Pin Count: 30 pins for extensive connectivity options.
- Input Voltage Range: Accepts 7V to 12V DC (Vin).
- Output Voltage: Delivers 5V DC (regulated) for connected components.
- Dimensions: Compact at 60mm x 30mm x 10mm.
- Weight: Approximately 25 grams for easy handling.
-
Pro Mini – ATMEGA 328P – 5V/16Mhz – Compatible Board
₹1,399.00₹899.00- Circuit Operating Voltage: 5V
- Clock frequency: 16MHz.
- Digital I/O Pins: 14
- 8 analog input port: A0 ~ A7.
- A pair of TTL level serial port transceiver : RX / TX.
- 6 PWM port: D3, D5, D6, D9, D10, D11.
- Use For Atmel Atmega328P-AU microcontroller.
-
QBM ARDUINO OPEN SOURCE BOARDS ARDUINO MICRO
₹1,999.00₹1,599.00Model Type Arduino Micro Color Blue Microcontroller ATmega32U4 Operating Voltage (VDC) 5 Input Voltage(Recommended) 7-12V Analog I/O Pins 12 Digital I/O Pins 20 PWM Output Pins 7 Architecture AVR Clock Speed 12 MHz DC Current per I/O Pin (mA) 20 Flash Memory 32 KB EEPROM 1 KB (ATmega32U4) SRAM (KB) 2.5 Weight (gm) 13 Length (mm) 48 Width (mm) 18 Height (mm) 8 -
QBM ARDUINO OPEN SOURCE BOARDS ARDUINO NANO
₹1,199.00₹899.00- Microcontroller Atmel ATmega328 SMD Package
- Operating Voltage (logic level) 5 V
- Input Voltage (recommended) 7-12 V
- Input Voltage (limits) 6-20 V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins 8
- DC Current per I/O Pin 40 mA
- Flash Memory 32 KB (of which 2KB used by bootloader)
- SRAM 2 KB
- EEPROM 1 KB
- Clock Speed 16 MHz
- Dimensions 0.70” x 1.70”
-
QBM Mega 2560 R3 Board – Compatible Model High Quality
₹2,199.00₹1,799.00- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 256 KB of which 8 KB used by bootloader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
- USB Host Chip: MAX3421E
- Length:101.98mm/4.01i
- QBM
- Width:53.63mm/2.11in
- Height:15.29mm/0.60in
-
RAMPS 1.4 3D Printer Controller Board Arduino Mega Shield (RED) 2560 RAMP
₹499.00₹299.00- Supply Voltage: 12V
- Standard interfaces (as that of the extruder)
- Reserved GCI like I2C and RS232
- 3 MOSFET’s are applied to the heater/ fan and thermistor circuit.
- Another 5A added to protect the component parts.
- An 11A fuse is added to the hotbed.
- Support 5 stepper drive board
- The adoption of Pin Header as Pololu makes it more convenient to repair or change.
- I2C and SPI are reserved for expanding
- All the MOSFET can be controlled by PWM
- Use the interface of the servo motor to adjust the level of the printing platform automatically.
- Adding an SD module for SD ramps module.
- LED can indicate the status of the heater (the open and close of MOS).
- Expandable to control other accessories.
- Palolo boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
- 2 stepper motor for Z axis in parallel.
-
UNO PROTOTYPE SHIELD with 170PTS BREADBOARD for Arduino UNO ABREAD
₹599.00₹149.00- It has a nice standard 0.1″x0.1″ prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- An IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- Two 3mm general use LEDs, red and green, as well as 2 matching resistors
-
UNO R3 TFT SCREEN ADAPTER ZA010
₹499.00₹349.00- TFT01 LCD screen works at 3.3V voltage, it cannot be used directly on standard Arduino board, so for TFT01 screen to be compatible with standard Arduino board, TFT sec Shield, can be directly connected to the Arduino board.
- [TFT01 LCD 16] TFT01 LCD 16 can support the current mode, since there is enough Mega2560 IO, although only a touch screen interface or SD card interface is used, such as the ca328 will not exist.
- [8-bit mode] TFT01LCD supports 8-bit mode, you can use SD card interface and touch screen interface at the same time, adopt voltage division IC, have TFT as screen more stable.
- [3.2 Inch] 3.2 inch TFT LCD screen, can be directly to the 3.2 “TFT on the screens, it can be compatible with the Arduino.
- [Applicable] This Arduino Mega V2.2 TFT01 LCD is fit for 3.2 inch TFT LCD module; The MEGA TFT01 shield supports 16-bit mode; Because Mega Board has enough pins to use SD card shield and touch function at the same time.
-
WEMOS D1 R2 WMOD1
₹599.00₹349.00- Microcontroller: ESP8266EX
- Operating Voltage: 3.3V
- Digital I/O Pins: 11 (all I/O pins have interrupt/PWM/I2C/one-wire capability, except for D0)
- Analog Input Pins: 1
- Flash Memory: 4MB
- 6. On-Board Switching Power Supply:
- Input Voltage Range: 9V to 12V
- Output: 5V at 1A Max