Showing 226–250 of 404 results
-
Liquid pH Value Detection Sensor Module with PROBE (PHSENS+PHPROB)
₹1,499.00₹1,299.00Add to cart- PH range: 0-14 PH
- Temperature range: 0-60℃
- Zero-point: 7 ± 0.5PH
- Alkali Error: 0.2PH
- Theoretical Percentage Slope: ≧98.5%
- Internal Resistance: ≦250MΩ
- Response Time: ≦1min
-
Liquified Isobutane LPG Propane Gas Sensor Module MQ6
₹199.00₹139.00Add to cart- High Sensitivity to LPG, iso-butane, propane
- Small sensitivity to alcohol, smoke
- Good sensitivity to Combustible gas in wide range
- High sensitivity to Propane, Butane, LPG and also response to Natural gas
- Long life and low cost
- Simple drive circuit
-
Liquified Methane Gas Sensor Module MQ5
₹399.00₹199.00Add to cart- This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ5 gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins and you are ready to go.
- For Digital output the threshold value can be easily set by an on-board potentiometer. Using this module you can easily interface MQ5 gas Sensor to any Microcontroller, Arduino or even Raspberry Pi.
- This Gas Sensor module is sensitive to LPG, natural Gas & Town Gas. it is also small sensitivity to alcohol & smoke.
-
LM2596 2A Buck Step-down Power Converter Module DC 4 ~ 40 to 1.3-37V LED Voltmeter LM2596D
₹249.00₹149.00Add to cart- Input Voltage(VDC): 4 ~ 40.
- Output Voltage(VDC): 1.3 ~ 37.
- Output Current: 2A Rated, ( 3A maximum with heat sink).
- Switching Frequency: 150 kHz.
- Input reverse polarity protection.
- Built-in output short protection function.
-
LM2596S DC-DC Stepdown Power Supply Module 3A LM2596
₹199.00₹99.00Add to cart- Input voltage: 3-40V
- Output voltage: 1.5-35V(Adjustable)
- Output current: Rated current is 2A, maximum 3A
- Switching Frequency: 150KHz
- Operating temperature: Industrial grade (-40 to +85 )
- Conversion efficiency: 92%(highest)
-
LM35D Analog Temperature Sensor Module + Cable LM35D
₹249.00₹129.00Add to cart- Based on the semiconductor LM35 temperature sensor
- Can be used to detect ambient air temperature
- Calibrated directly in °Celsius (Centigrade)
- Linear + 10 mV/°C Scale Factor
- 0.5°C Ensure accuracy (at +25°C)
- Low power consumption, less than 60uA
- Low output impedance, 1mA current through only 0.1Ω
- With screw holes for easy installation and fixed. Aperture 2.6mm
-
LM35DZ ANALOG TEMPERATURE SENSOR LM35DZ
₹199.00₹99.00Add to cart- Sensor type: temperature sensor
- Kind of temperature sensor: analog, with voltage output
- Calibrated directly in: °Celsius (Centigrade)
- Temperature measuring range: 0…100°C
- Scale factor: Linear 10.0 mV/°C
- Case: TO92
-
LOAD CELL 50KG LOAD50
₹899.00₹399.00Add to cart- Capacity (Kg): 50.
- Output Sensitivity (mv/v): 1.0±0.1.
- Nonlinearity (%FS): 0.03.
- Repeatability (%FS): 0.03.
- Input Resistance (Ω): 1000.
- Insulation Resistance (MΩ): ≥5000.
-
MAX 3232 DB9 RS232 CONVERTER Module M3232
₹199.00₹99.00Add to cart- IC Chip: MAX3232
- Operating Voltage: 3.3-5.5V
- It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N -2EC MCU
- Pre-assembled compact size board
- Suitable for use with most microcontrollers
- Operates up to 250 kbit/s
-
MAX30102 OXYMETER MAX302
₹299.00₹139.00Add to cart- VIN: Main Power Input 1.8V-5V
- 3-Bit Pad: I2C Bus Pull Up Level, You Can Choose 1.8V or 3.3V According to the Pin Master Voltage
- SCL: I2C Bus Clock
- SDA: Connected to the I2C Bus Data
- INT: MAX30102 Chip Interrupt PIN
- RD: MAX30102 Chip’s RD LED Grounding Terminal, Generally Doesn’t Need to Connect
- IRD: MAX30102 Chip’s IR LED Grounding Terminal, Generally Doesn’t Need to Connect
- GND: Grounding Wire
-
MAX30102 Pulse Oximeter Heart Rate Sensor Module MAX301
₹399.00₹159.00Add to cart- Highly-integrated, small-size sensor
- Non-chest based heart-rate/SpO2 detection
- Ultra-low power consumption
- Size: 1.27cm x 1.27cm
-
MCP2515 CAN BUS Module TJA1050 REC SPI 51 Single CAN2515
₹199.00₹139.00Add to cart- Support CAN V2.0B technical standard, communication rate 1Mb/S.
- Use High-speed CAN transceiver TJA1050
- Dimension: 40×28mm
- SPI control for expand Multi CAN bus interface
- 8MHZ crystal oscillator
- 120Ω terminal resistance
- Module 5V DC power supply.
- 0 to 8 bytes long data field.
- Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation
- The working current: typical 5mA, standby current 1 microamp. Except for the power indicator.
- Use serial port could view the communication data
- With the independent key, LED indicator, Power indicator
- With power pin
- Standard frames, extended frames, and remote frames.
- Positioning screw hole centre spacing 23 mm x 38 mm
-
Mercury Ball Tilt Switch 5mm (Pack of 10) MERC5
₹249.00₹135.00Add to cart- Operating Voltage: 3.3V to 5V
- Diameter: 4mm
- Length: 35mm
- Output Format: digital switching outputs (0 and 1)
-
MFRC 522 Rfid Module With RF Card and Fob RC522K
₹199.00₹159.00Add to cart- Operating Current :13-26mA / DC 3.3V
- Idle Current :10-13mA / DC 3.3V
- Sleep Current: < 80uA
- Peak Current: < 30mA
- Operating Frequency: 13.56MHz
- Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, mifare Pro, MIFARE DESFire
- Environmental Operating Temperature: -20 – 80 degrees Celsius
- Environmental Storage Temperature: -40 – 85 degrees Celsius
- Relative humidity: relative humidity 5% – 95%
- Reader Distance: ≥ 50mm / 1.95″ (mifare 1)
- Module Size: 40mm × 60mm
- Module interface: SPI
- Data transfer rate: Maximum 10Mbit/s
-
MH-M18 Wireless Bluetooth Audio Receiver Board Module BLT 4.2 mp3 lossless decode
₹299.00₹199.00Add to cart- Support WAV/WMA/FLAC/APE/MP3 lossless decoding, stereo two-channel output
- Support Bluetooth Protocol HFPV1.7, A2DPV1.2, AVRCPV1.5, AVCTPV1.2, AVDTPV1.2
- Maximum Transmission Distance of 20 meters.
- Can be powered via lithium Battery.
-
MICRO SD CARD MINI T/F CARD MODULE AA115
₹199.00₹89.00Add to cart- Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
- The level conversion circuit board that can interface level is 5V or 3.3V
- Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
- Communication interface is a standard SPI interface
- 4 M2 screw positioning holes for easy installation
- Size: 4.1 x 2.4cm
-
Micro SD Card Reader Module
₹99.00₹69.00Add to cart- Power Supply: 4.5V – 5.5V, 3.3V
- Positioning Holes: 4 M2 screws positioning hole diameter of 2.2mm
- Control Interface: GND, VCC, MISO, MOSI, SCK, CS
- Size: 45 x 28mm
- Net weight: 6g
-
MICRO USB TO 5 PIN ADAPTER BOARD AA769
₹99.00₹49.00Add to cart- Mini Micro USB To DIP 2.54mm Adapter
- Widely used in electronic product links
- MICRO USB to DIP Adapter 5pin female connector B type pcb converter pinboard 2.54
- 5 Pin Female Connector B Type
-
Microwave Doppler Radar Wireless Motion Sensor Module HB100
₹499.00₹199.00Add to cart- Low current consumption (typical 30 mA)
- CW or pulse operation
- Flat profile
- Long detection range (20 m)
- Supply voltage: 4.75V to 5.25V
- X-Band Frequency: 10.525 GHz
- Minimum Power Output: 13 dBm EIRP
-
MINI DC-DC Boost Module (0.9V~5V) 5V 600MA USB USB6M
₹199.00₹99.00Add to cart- Input voltage: 0.9-5V DC
- Output voltage: 5V DC
- Output Current: 500-600mA
- Load regulation: ±1%
- Voltage regulation: ±0.5%
- Switching frequency: 500KHz
- The module adopts a high-performance imported chip, performance is superior to the common module.
- Work with indicator light.
- Take the USB female, a wide range of Uses.
- A single AA battery power supply can output current up to 200~300 ma.
-
MINI MICRO SD CARD READER MODULE AA115M
₹199.00₹79.00Add to cart- Supports FAT file system SD carrier
- Supports playing of 4Bit ADCPM format files
- Recognize the voice files automatically
- Support microprocessor and key control
- Audio output: 16bitDAC and PWM
- Maximum voice storage: 512 voice
- Operating voltage: DC 2.6 to 3.6V
- Quiescent current: 16 A (SD card is not inserted
-
Momentary Tactile Push Button Module DC 5V Switch TACTS
₹99.00₹79.00Add to cart- Momentary Action: Activates circuits only while pressed, ideal for temporary control applications.
- Tactile Feedback: Provides a satisfying click sensation, enhancing user experience and precision.
- Standard DC 5V Operation: Compatible with most microcontrollers and development boards for versatile use.
- Compact and Lightweight: Space-saving design suitable for easy integration into various electronic projects.
- Breadboard Compatible: Easily fits into standard breadboards for quick prototyping and experimentation.
- Durable Construction: Designed for longevity and reliable performance, even with frequent use.
- Versatile Applications: Perfect for DIY electronics, robotics, Arduino, Raspberry Pi projects, and more.
- Easy to Install: Simple connections make it user-friendly for both beginners and experienced developers.
-
MPU-6050 GY-521 3AXIS ACCELEROMETER+GYROSCOPE M6050
₹399.00₹159.00Add to cart- MEMS 3-aixs accelerometer and 3-axis gyroscope values combined
- Power Supply: 3-5V
- Communication : I2C protocol
- Built-in 16-bit ADC provides high accuracy
- Built-in DMP provides high computational power
- Can be used to interface with other IIC devices like magnetometer
- Configurable IIC Address
- In-built Temperature sensor
-
MPU6050 – Triple Axis Gyro Accelerometer Module
₹599.00₹149.00Add to cart- Uses the popular MPU6050 IC
- MPU6050 contains a 3 axis Accelerometer and Gyroscope in a single package and simplifies design and usage. It also reduces cross axis alignment issues unlike other sensors with separate accelerometer and gyroscope ICs
- Digital I2C interface to read the output of the sensor
- Input Voltage: 2.3 – 3.4V
- Selectable Solder Jumpers on CLK, FSYNC and AD0
- Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of ±250, ±500, ±1000, and ±2000dps
- Tri-Axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
- Embedded algorithms for run-time bias and compass calibration. No user intervention required
- Digital-output temperature sensor
-
MPU9250 9 AXIX ATTITUDE GYRO SENSOR MODULE M9250
₹599.00₹339.00Add to cart- Accelerometer, Gyroscope, and Magnetometer
- Power Supply: DC3.3V-5V
- Chip: MPU9250
- Size: 22 mm x 17 mm.
- Gyro range : ± 250 500 1000 2000 ° / s
- Acceleration range: ± 2 ± 4 ± 8 ± 16g
- Magnetic field range: ± 4800uT
- 9 DOF modules
