Showing 126–150 of 401 results
-
DC12-80V 600W ADJ. Volt. Constant Current Module NA66B
₹999.00₹799.00Add to cart- Module Type: Step-Up (Boost)
- Input voltage: 12V-60V
- Input Current: Maximum input current 15A
- Output voltage: 12V-80V adjustable
- Output Current: Maximum output current 10A
- Output Power: 600W
- Short circuit protection: Fuse (Input 20A Fuse)
- Overcurrent protection: Yes
-
DC5V HUMIDIFIER USB SPRAY MODULE 108KHZ HUM108
₹149.00₹110.00Add to cart- Product Name: 108KHz 20mm USB Humidifier
- Work Voltage: DC 4.5V~5.0V
- Work Power:2W
- Work Frequency:108KHz(+/-3KHz)
- Power Type: Female USB Socket
- Diameter without rubber ring:16mm
- Diameter with rubber ring:20mm
- Spray Diameter:5um
- Spray Hole:740 holes
- Spray speed:50ml/h
- Work Temperature:0℃ ~ 85℃
- Work Humidity:10%~90%RH
- Driver Size:35*19*15mm
- Length: 35 mm
- Width: 19 mm
- Height: 15 mm
- Weight: 10 gm
-
DHT11 Temperature And Humidity Sensor Module DHT11
₹299.00₹199.00Add to cart- Power Supply: 3.3~5.5V DC
- Output: 4 pin single row
- Measurement Range: Humidity 20-90%RH, Temperature 0~50℃
- Accuracy: Humidity +-5%RH, Temperature +-2℃
- Resolution: Humidity 1%RH, Temperature 1℃
-
DHT22 Temperature and Humidity Module DHT22
₹399.00₹149.00Add to cart- Supply voltage: 5V
- Temperature range:-40-80℃ resolution0.1℃ error <±0.5℃
- Humidity range:0-100%RH resolution0.1%RH error±2%RH
- Sequence of the line:VCC,GND,S
- Size: 38 x 20mm
-
DIGITAL BAROMETRIC PRESSURE SENSOR MODULE BMP180
₹199.00₹99.00Add to cart- Can measure temperature and altitude.
- Pressure range: 300 to 1100hPa
- High relative accuracy of ±0.12hPa
- Can work on low voltages
- 3.4Mhz I2C interface
- Low power consumption (3uA)
- Pressure conversion time: 5msec
- Potable size
- Operating voltage of BMP180: 1.3V – 3.6V
- Input voltage of BMP180MODULE: 3.3V to 5.5V
- Peak current : 1000uA
- Consumes 0.1uA standby
- Maximum voltage at SDA , SCL : VCC + 0.3V
- Operating temperature: -40ºC to +80ºC
-
Digital LDR Module – 3 Pin
₹49.00₹39.00Add to cart- LM393 based design.
- Can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- LEDs indicating output and power.
- Operating Voltage: 3.3V to 5V DC.
- Operating Current: 15ma.
-
Digital Thermometer Waterproof TPM-10 TPM10
₹199.00₹99.00Add to cart- Temperature range: -50°C ~ +110°C
- Temperature display resolution: ±0.1
- temperature measurement accuracy: 1°C
- Cable Length: 1M
- Display Dimensions : 48 x 29 x 16 (LxWxH) mm.
- The module is powered by a pair of LR44 button batteries (battery included)
-
DIP 3 Color LED Module COL3
₹199.00₹49.00Add to cart- The use of plug-in full-colour LED.
- RGB trichromatic limiting resistor to prevent burnout.
- With a variety of single-chip interface.
- Through the PWM adjusting, three primary colors can be mixed to obtain different colors
- The working voltage: 5V
-
DOUBLE SPEED MEASURING SENSOR MODULE HC020
₹199.00₹99.00Add to cart- Working voltage: 4.5V to 5.5 V
- Transmit tube pressure drop: Vf = 1.6 V
- Transmit tube current: 20 mA
- Distinguish precision: 0.01 mm
- Measurement frequency, 100 kHz
-
Dry Reed Sensor Module Magnetic Switch REED
₹99.00₹59.00Add to cart- Open reed switch
- Working voltage: 3.3V ~ 5V
- Current: Upto 1.2A
- Comparator output, clean signal, great waveform, and strong driving ability
- Digital switch output (0 and 1)
- Fixed bolt hole for easy installation
-
DS18B20 Digital Temperature Sensor Module DS18B20M
₹199.00₹99.00Add to cart- Digital signal output
- 18B20 Temperature Sensor Chip
- Resolution adjustment ranges from 9-12 bytes.
- Send data via a pin
- Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.
-
DS18B20 Waterproof Digital Thermal Probe 1M AB117
₹199.00₹165.00Add to cart- A probe by new original installation import DS18B20 temperature sensor chip.
- Stainless steel tube encapsulation waterproof moisture proof prevents rust.
- Stainless steel shell (6 * 45 mm), lead length 100 mm (shielding wire) use stability;
- 3.0 V-5.5 V power supply;
- Temperature range wide: -55 ℃ ~ + 125 ℃;
- Without the external components, the unique single bus.
-
DS3231 RTC MODULE FOR RASPBERRY PI (WITHOUT BATTERY) DS3231R
₹399.00₹249.00Add to cart- High-Precision Timekeeping: Features the DS3231 RTC chip with a temperature-compensated crystal oscillator (TCXO) for accurate time and date tracking.
- I2C Interface: Connects easily to Raspberry Pi via the I2C communication protocol for seamless integration.
- Battery Backup Ready: Supports a CR2032 battery (not included) for maintaining timekeeping during power outages.
- Wide Operating Temperature: Works reliably in temperatures ranging from -40°C to +85°C.
- Compact and Lightweight Design: Easy to integrate into projects without taking up much space.
- Low Power Consumption: Consumes minimal energy, preserving backup battery life.
- Automatic Leap Year Compensation: Handles leap years automatically, ensuring correct time up to 2100.
- Ideal for Raspberry Pi Projects: Perfect for data logging, IoT devices, scheduling systems, and more.
-
DSO138 2.4 inch TFT Handheld Pocket-size Digital Oscilloscope Kit DIY Parts Electronic Learning Set Soldered
₹2,299.00₹1,899.00Add to cart- This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as the ARM test development board.
- Can be secondary development on the basis of this kit, for example, it can be changed to Milli voltmeter, data loggers.
- Adjustable vertical displacement, and with instructions.
- With automatic, regular and one-shot modes, easy to capture the moment waveform.
- Available rising or falling edge trigger.
- Observable previous trigger waveform (negative delay).
- Can freeze at any time waveform display (the HOLD function).
- Comes 1Hz /3.3V square wave test signal source.
-
Dual Axis PS2 game Joystick Module AB001
₹199.00₹79.00Add to cart- Optional momentary switch is operational at all rotations, Long life, 1 million cycles
- Two analog outputs, one digital output
- X, y-axis output of the two potentiometers can be read out through the a to d converter.
- Quality rocker, long life, stable performance
- 2.54mm pin interface and leads Long service life and stable performance with standard interface and electronic building blocks, it is widely use in DIY projects
-
E18-D80NK ADJ. INFRARED SENSOR SWITCH 3-80CM E18D80
₹399.00₹179.00Add to cart- Sensing range: 3 – 80cm.
- Input voltage: 5VDC.
- Current Consumption: 100mA.
- Digital Output.
- Cable length: 1 m.
- Diffuse reflective type
-
E18-D80NK Adjustable IR Sensor Proximity Switch 3-80cm Range
₹399.00₹199.00Add to cart- Less influence on the color of reflected objects, reflectivity.
- Compact size.
- Industrial grade quality.
- Can detect colour difference from certain range.
- TTL output low whenever sensor senses a obstacle.
- Adjustable Detection distance of 3cm to 80cm.
- External control circuit unnecessary.
- Low cost.
- Output indication LED.
- Digital output.
- Low consumption.
-
Electronic Building Blocks Big Key Button Module BUTMC
₹299.00₹110.00Add to cart- Analog acquisition, press the different buttons of different voltage output.
- Port compatible sensor expansion board.
- Output high level when pressed, release to keep low level.
-
EM-18 RFID Reader Module
₹499.00₹299.00Add to cart- Operating Voltage: 5V DC Supply
- Reading Distance: 6-10 cm.
- Read frequency: 125 kHz.
- EM4001 64 – bit RFID tag compatible.
- 9600bps ASCII output.
- Current : <50 mA
- Operating Frequency : 125 Khz
- Read Distance : 5 cm
- Compatible Tags : 125KHz EM4100 Tags
-
EM18 RFID Reader Module EM18
₹699.00₹299.00Add to cart- Operating Voltage: 5V DC Supply
- Reading Distance: 6-10 cm.
- Read frequency: 125 kHz.
- EM4001 64 – bit RFID tag compatible.
- 9600bps ASCII output.
- Current : <50 mA
- Operating Frequency : 125 Khz
- Read Distance : 5 cm
- Compatible Tags : 125KHz EM4100 Tags
-
EMG Muscles Sensor Module EMGM
₹1,999.00₹1,299.00Add to cart- Real-Time Monitoring: Accurately detects and measures electrical activity from muscle contractions
- Output Type: Analog signal (0-5V) for easy interfacing with microcontrollers and processors
- Sensitivity: High sensitivity to low-level muscle signals, suitable for small muscle movements
- Operating Voltage: 3.3V to 5V DC, compatible with common microcontroller systems
- Bandwidth: 20 Hz to 500 Hz, suitable for detecting typical EMG signal frequencies
- Signal Amplification: Built-in amplification for clearer and more accurate muscle signal output
- Compact Size: Small form factor (3.5 x 2.5 x 1 cm) for easy integration into wearable devices and prosthetics
- Low Power Consumption: Designed for efficient use, ideal for long-duration applications
- Interface Compatibility: Works with Arduino, Raspberry Pi, and other microcontroller platforms
- Durable Construction: Built for long-lasting reliability and performance in various applications
- Applications: Ideal for use in prosthetics, rehabilitation, muscle control systems, biofeedback, sports science, and medical research
- Certifications: CE and RoHS compliant for safety and environmental standards
-
ENC28J60 Ethernet LAN Module E28J60
₹499.00₹329.00Add to cart- ENC28J60 Ethernet chips, SOP28 package
- SPI Interface
- 1×10 connector, can be easily mounted with the MCU
- Built-in isolation transformer RJ45 connectors HR911105A
- Power LED
- Single Supply: +3.3 V
- 25Mhz Crystal
- PCB size: 48×18 mm
-
ESP-12 D1 MINI V2-MINI NODE MCU 4M BYTES LUA WIFI WED1M
₹399.00₹209.00Add to cart- 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Use BRT (Bias Resistor Transistor), easier into flash mode.
- 30% increase in radiating area, more stable.
- Dimensions : 35 x 26 x 8 (LxWxH) mm.
- Weight: 10 gm.
- Board Color : Blue
- Compatible with Arduino
- Compatible with NodeMCU
- Compatible with MicroPythonz
-
ESP-12E ESP8266 SERIAL WIFI MODULE ESP12
₹299.00₹159.00Add to cart- Communication Interface Voltage: 3.3V
- Working Current: 240mA(MAX)
- Serial Port Baud Rate: 115200 (Default), can be modified to other values by AT command
- Serial Communication Format: 8N1
- Wireless Network Mode: Station / Sofa / Sofa station
- Wireless Criteria: 802.11 b / g / n
- WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
- 19.5dBm output power
